Highway09a Ic Datasheet Pdf ❲FAST❳

Dual output pins for delivering processed control signals to external components. Enable or disable functionality for the entire IC. Primary Applications

+-----------------------------------+ | 32 31 30 29 28 27 26 25 | | VDD GND NC RX+ RX- TX+ TX- VDD_A | (RST) 1 | 24 | CLK_IN (SDA) 2 | 23 | CLK_OUT (SCL) 3 | 22 | GPIO_0 (INT) 4 | HIGHWAY09a 21 | GPIO_1 (MISO) 5 | TOP VIEW 20 | GPIO_2 (MOSI) 6 | 19 | GPIO_3 (SCLK) 7 | 18 | CS_N (SS_N) 8 | 17 | AGND | 9 10 11 12 13 14 15 16 | | VIO GND VREF A0 A1 REG OUT TEST | +-----------------------------------+ Pin Description Table Pin Number Description Active-Low Hardware Reset Pin I2Ccap I squared cap C Control Interface Data and Clock lines Interrupt Output (Active-Low, Open-Drain) 5, 6, 7, 8 MISO, MOSI, SCLK, SS_N SPI Peripheral Interface lines I/O Pad Reference Voltage (1.8V to 3.3V) Digital Ground Reference Internal Voltage Regulator Reference Output Hardware Address Select Pins for I2Ccap I squared cap C Internal LDO Regulator Filter Capacitor Connection Auxiliary Analog Driver Output Factory Test Mode Pin (Must be tied to GND) Analog Ground Reference Chip Select Line (Active-Low) GPIO_3 - GPIO_0 General Purpose Input/Output Pins CLK_OUT, CLK_IN Crystal Oscillator / External Clock Connections 3.3V Analog Power Supply Differential Transmit Pair (High-Speed Highway Bus) Differential Receive Pair (High-Speed Highway Bus) No Internal Connection 3.3V Digital Power Supply 5. Electrical Characteristics DC Characteristics measured at VDDcap V sub cap D cap D end-sub = 3.3V, GND = 0V, TAcap T sub cap A = 25°C unless otherwise noted. Low-Level Input Voltage ( VILcap V sub cap I cap L end-sub ): -0.3Vnegative 0.3 cap V High-Level Output Voltage ( VOHcap V sub cap O cap H end-sub ): IOHcap I sub cap O cap H end-sub Low-Level Output Voltage ( VOLcap V sub cap O cap L end-sub ): 0.4V0.4 cap V IOLcap I sub cap O cap L end-sub Active Power Supply Current ( IDDcap I sub cap D cap D end-sub ): 35 mA (Typical at 100 MHz operation) Standby Current ( ISTBYcap I sub cap S cap T cap B cap Y end-sub ): 12 A (Typical, all clocks gated) 6. Layout Guidelines and Application Circuitry

Below is a technical data sheet and application guide developed for the .

The designation "Highway09a" is often the specific model code used by various Chinese manufacturers or module resellers for this standard design. Highway09a Ic Datasheet Pdf

Network switching sub-cards and line card diagnostic units. 2. Key Features and Technical Highlights

Current sensing signals used to monitor power levels and prevent overloads.

Comprehensive Guide to the HIGHWAY09A IC: Datasheet, Pinout, and Application Architecture Dual output pins for delivering processed control signals

Enables precise management of motor speed or high-power heating elements through specific control pins (CTRL1, CTRL2).

Searching for a on general search engines can lead to forums, third-party retailers, or outdated copies. Using the official datasheet is non-negotiable for several reasons:

This public link is valid for 7 days and shares a thread, including any personal information you added. This link or copies made by others cannot be deleted. If you share with third parties, their policies apply. Can’t copy the link right now. Try again later. The designation "Highway09a" is often the specific model

The HIGHWAY09A is a purpose-built microcontroller for induction heating systems. Its feature set is tailored for the specific demands of this application:

To summarize:

Assuming the Highway09a is a CAN transceiver, a typical application circuit from the datasheet would include:

Programmable Logic Controllers (PLCs), sensor data aggregation, and factory automation nodes.